Illustrative sample — fictional products, fixed report. Free, no account.
SpecRelay substitution review
Illustrative sample: kitchen undermount sink swap
- A · Approved:
- Example Sink Co. ES-3321-U (fictional)
- B · Proposed:
- Sample Basin Works SB-850UM (fictional)
9
Documented change
1
Confirm
8
Same
Documented changes
FieldA · ApprovedB · ProposedNote
Manufacturer / brand
A: Example Sink Co.
B: Sample Basin Works
Documented changeDocumented values differ as written.
Model number
A: ES-3321-U
B: SB-850UM
Documented changeDocumented values differ as written.
Gauge
A: 16
B: 18
Documented changeDocumented change: +2.
Overall front-to-back
A: 21 1/4 in
B: 559 mm
Documented changeDocumented change: +19.25 mm (+0.76 in).
Bowl depth
A: 9 in
B: 254 mm
Documented changeDocumented change: +25.4 mm (+1 in).
Drain location
A: Rear center
B: Rear offset left
Documented changeDocumented values differ as written.
Certifications / listings
A: cUPC, ASME A112.19.3
B: cUPC
Documented changeDocumented values differ as written.
Included accessories
A: bottom grid, strainer, mounting clips, cutout template
B: strainer, mounting clips
Documented changeDocumented values differ as written.
Warranty
A: Limited lifetime
B: 10 years
Documented changeDocumented values differ as written.
Items to confirm
FieldA · ApprovedB · ProposedNote
Weight
A: 28 lb
B: not found
ConfirmNot found on the proposed sheet. Confirm with the manufacturer — do not assume it matches.
Same as documented
FieldA · ApprovedB · ProposedNote
Product type
A: Single bowl kitchen sink
B: Single bowl kitchen sink
SameSame as written.
Mounting / installation type
A: Undermount
B: Undermount
SameSame as written.
Material
A: Stainless steel
B: Stainless steel
SameSame as written.
Finish / color
A: Brushed satin
B: Brushed satin
SameSame as written.
Overall length / width (L-R)
A: 33 1/2"
B: 851 mm
SameEquivalent after unit mapping (within rounding).
Minimum cabinet size
A: 36 in
B: 914 mm
SameEquivalent after unit mapping (within rounding).
Drain opening size
A: 3 1/2 in
B: 89 mm
SameEquivalent after unit mapping (within rounding).
Faucet holes
A: 0
B: 0
SameSame as written.
Questions by trade
designer/owner
- Confirm the brand change is acceptable to the owner and any warranty terms.
- Confirm the exact model number ordered matches the sheet reviewed.
- Is the gauge change acceptable (lower number = thicker steel)?
- Confirm listings required by the jurisdiction or project spec (e.g. as named on the original approval) still appear.
- Confirm what was included before (grid, strainer, clips, template) is still included or ordered separately.
- Confirm the warranty term is acceptable to the owner.
fabricator
- Does front-to-back still leave the required setback from the counter edge and backsplash?
- Is the support method adequate for this weight (clips, rails, or under-support)?
plumber
- With the new bowl depth, does the tailpiece and trap still reach the wall drain height without lowering it?
- Plumber: does the drain location conflict with the disposal, trap arm, or cabinet stretcher?
- Confirm listings required by the jurisdiction or project spec (e.g. as named on the original approval) still appear.
- Confirm what was included before (grid, strainer, clips, template) is still included or ordered separately.
cabinet installer
- With the new bowl depth, does the tailpiece and trap still reach the wall drain height without lowering it?
- Plumber: does the drain location conflict with the disposal, trap arm, or cabinet stretcher?
- Is the support method adequate for this weight (clips, rails, or under-support)?
This compares only what the two documents state. It does not certify fit, code compliance or compatibility. Confirm with the manufacturer and the installing trades.
Ready to check your own approved and proposed sheets?
Compare two spec sheets